Catalog Part Matches (9735)
7004764 Cable Assembly, Counter Balance Counter balance cable used Cybex models: Smith Machine - 5341. | |||
7016528 Knob, Oval Oval shaped knob. NOTE: If you have not used an upgrade kit on your machine, you can use 7023651 as a generic replacement for the Knob. | |||
9001593 Roller, Rear Rear roller. Please note this machine came with two different size rollers. This roller is 25.5". | |||
3025616 Bearing, With block Linear bearing with mounting block used on Life Fitness models: PL06 - Smith Machine | |||
44000927 Belt, Drive Drive belt Please note, different versions of this machine used two different length belts. This belt is 61" if you need the 29" you will nee. . . | |||
44000125 Belt, Drive Drive belt Please note, different versions of this machine used two different length belts. This belt is 29" if you need the 61" you will nee. . . | |||
39001598 Cable, Ab Crunch 161.5" Ab Crunch Cable ***NOTE*** Two differrent length cables were used for this machine. Please verify the length of the cable you are repl. . . | |||
10004339 Cable Assembly 134" Lat puldown cable for the Paramount FL-33 Lat pulldown machine. | |||
6073957 Retainer, Key Machine retainer key. | |||
40000979 Cable, Ratio 4:1 Cable Ratio 4:1 The 4-1 ratio machine will have two pulleys at the top of each weight stack | |||
3092811 Controller, Motor, Refurbished REFURBISHED motor control board. This is for the domestic machine only. | |||
58000325 Cable, Lat Pull Down, 150" The Weight Stack cable End on this machine has a Ball stud that attaches the Cable end to the Weight Stack. NOTE: If your cable end is a Threaded S. . . | |||
40000978 Cable 2:1 Ratio Cable 2:1 Ratio The 2-1 ratio machine will have one pulley at the top of each weight stack | |||
24003375 Cable Assembly, 271" Low Pulley Cable Assembly NOTE: The cable assembly you receive may not be able to be taken apart for routing on the machine. If you cannot route the cabl. . . | |||
16000701 Motor, Resistance Resistance motor used on Diamondback models: 460EL, 460R, 46U. NOTE: The white cam will have to be adjusted during install because each machine m. . . | |||
6072015 Roller, Front Front drive roller This is an upgraded roller, the shafts are now 5.8". If your original was 1/2" you will need to remover the bushing before insta. . . | |||
41000122 Handle, Release Release handle used on Free Motion Squat machine. | |||
6074705 Cable Assembly, 141" Cable Assembly with attaching wieght shaft piece. NOTE: This cable comes with one "blank" end. The hardware for the blank end will come unattached to t. . . | |||
58000252 Pin, 10lb Pin, 10lb NOTE: The manufacturer used a few different types of pin on this machine. You will receive whatever we have in stock. | |||
6044565 Grip, Hand Hand grip. ***These will need to be cut to length as they will be longer than the original on the machine*** | |||
24014156 Cable Assembly, Lat, 153", W/O Balls Lat cable without removeable balls. NOTE: There are (2) of the cables required per machine. We sell them as a single cable so order (2) if needed. There . . . | |||
52007849 Roller, Front Front roller. * Please note, many of these machines used different size rollers. Please contact us with your serial number to be sure to you get the roll. . . | |||
6029408 Motor, Resistance Resistance motor. NOTE: The white cam will have to be adjusted during install because each machine may have minor differences. The center phillips screw . . . | |||
62004167 Belt Belt This is a drive belt for the newer version of the machine this is a 42" belt if you need the 35" belt please order catalog# 62036638. **Please. . . | |||
6001977 Guide rod, 72" 72" long weight stack guide rod. Note: This rod does not have screw holes in the top. If your machine has holes in the top of the guide rod, you will hav. . . | |||
Showing Parts: 3651 - 3675 Of 9735 |